VIRSUN INDUSTRIES

Call us:

Send Inquiry Send Inquiry

Tile Adhesives
Product Image (34)

TILE ADHESIVE

Price: 100 USD ($)/Quintal

PLATINUM Substrate: The surface to be covered with Ceramic tile shall be sound and confirm to good design, rigid, clean and free of dirt, oil, grease, curing compounds, form release agents or loose plaster and paint. For economy the surfaces should be level and true with in: Walls 3mm in 2.5m Floors 1.5mm in 1.0m Surface Preparation: If a plaster/leveling mortar bed is applied, ensure that it is cured for at least 7 days to achieve proper strength before application of tile adhesive for installation of tile Ensure the substrate is clean and free from impurities like dust, dirt, debris, oil, grease, curing agents, loose plaster etc Dampen the wall before application of thin set adhesive Clean the back of tile for any dust or coating Mixing: The products can be mixed by hand or slow speed electric drill mixer (less than 300 rpm). Pour potable clean water in a clean container and then add the powder VIRSUN PLATINUM and mix until the mixture becomes creamy and plastic. Do not over mix. Leave the mix to slake for 5-10 min and remix before use. Mix only sufficient quantity of adhesive for immediate need. Proportion: Approximately 1 bag of VIRSUN PLATINUM with 5-6 ltrs of water. Adjust quantity of liquid to obtain proper consistency. Installation: Wet the surface and remove the excess water before applying the adhesive. Ensure the area is shaded from sunlight. The adhesive shall be applied with the flat side of the trowel using a scraping motion to work the material into good contact with the surface to be covered. Additional mortar is then applied with the notched edge of the trowel. When installing large tiles, spread adhesive onto back of tile in addition to trowelling material over surface to be tiled. Select proper type of notched trowel. a) Thin Tiles upto size 300 X 300 mm (1X1), use a square notched trowel of size 6mm X 6mm to provide a total thickness of 3mm b) Large Porcelain Tiles upto 450 X 450 mm with ribs, use a square notched trowel of size 6mm X 6mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 4.5mm c) Large Porcelain Tiles upto 600 X 600 mm (2X2) with ribs, use a square notched trowel of size 6mm X 9mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 6mm The most important standard to keep in mind is to insure that the piece of tile is completely bedded in the mortar or adhesive with 100% coverage. Rear face of tiles (especially Porcelain tiles) should be cleaned with damp sponge to clean all the dust. Do not saturate in water. Excess mortar on adhesive shall be cleaned from the surface of the stone with wet cloth or sponge while the mortar is fresh. Coverage Approx. 55-60 sq. ft. per 20 kg bag with a x (6mmx6mm) square notch trowel for a bed of 3mm. Color Grey Areas of Application Designed for internal floor applications Suitable Substrates Cement Mortar Beds Cement Plaster Brick Masonry Cement Terrazzo

Send Inquiry
Request To Call Back
Product Image (05)

Tile Adhesives

Price: 0.00 INR/Bag

Virsun Sun Fix Floor Tile Adhesive is bis approved isi standard is 15477:2019 type 1standrd a bagged cementitious powder to be mixed with water for installing ceramic the and natural stone using the thin-set method of Installation. Tile adhesives are a factory prepared blend of carefully selected raw materials. Portland cement and graded aggregates (Latex) are added to adhesive powders to increase bond strength. Best suited for Exterior and Interior Installation of ceramic/ vitrified/ Porcelain/Engineered stones and Natural Stone

Send Inquiry
Request To Call Back
Product Image (06)

WALL TILE ADHESIVE

Price: 0.00 INR/Bag

Virsun classic Floor Tile Adhesive is bis apoved isi standard is 15477:2019 type 1standrd en 1348 a bagged cementitious powder to be mixed with water for installing ceramic the and natural stone using the thinset method of Installation. Tile adhesives are a factory prepared blend of carefully selected raw materials. Portland cement and graded aggregates (Latex) are added to adhesive powders to increase bond strength. Best suited for Exterior and Interior Installation of ceramic/ vitrified/ Porcelain/Engineered stones and Natural Stones. Equivalent MYK laticrete 307 ULTRATECH VT WEBER Weberset Classic

Send Inquiry
Request To Call Back
Product Image (02)

STONE FIX ADHESIVE

Price: 0.00 INR

Virsun Apex Wall STONE Adhesives BIS 15477 standard and en 1348 standard a high-performance dry adhesive for use with water or latex for installing ceramic tiles, marble and stone using the thin-set installation method. For use In floor and wall Installations, It has high track and will hang walltIlewIlhout slippage. the tiles can be made Degree, cotton, double fired, single fired ceramic. Fixing poorly absorbent materials or non-absorbent materials such as single-fired tel refine porcelain stoneware and vIltlflecitIles. Suitable for use when high performances are required,such as tile fixing In Industrial environment or Una on fop of old ceramic tiles or natural stone indoors in swimming pools or on facades. Application Designed especially for interior & exterior door & wall installations of all types of tiles & stones.

Send Inquiry
Request To Call Back
Product Image (04)

SUN BLOCK ADHESIVE BLOCK BONDING MORTAR

Price: 240.00 INR

SUN BLOCK ADHESIVE AAC BLOCK JOINTING MORTAR. ASTM STANDARD 1660-9 SUN BLOCK ADHESIVE is a factory prepared blend of carefully selected raw materials, portland cement and graded aggregates and polymers. Designed for use with water to produce high strength thixotropic mortar, for laying aerated lightweight concrete, fly ash bricks, cement hollow blocks, cellular concrete blocks or smoothing over the block work surface in layers of up to 12mm thickness, that meet and exceed the requirements of National and International Approximately 200 sq.ft. per 50 kg bag when used at 2-3mm bed thickness Coverage is based on smoothness and evenness of the substrate, size of blocks used and the thickness of mortar used. Surface Preparation If a plaster/leveling mortar bed is applied, ensure that it is cured for at least 7 days to achieve proper strength before application of adhesive for construction of block work. Ensure the substrate is clean and free from impurities like dust, dirt, debris, oil, grease, curing agents, existing paints, loose plaster etc. Mixing The product can be mixed by hand Pour water in a clean container and then add the powder SUN Block adhesive until the mixture becomes creamy and plastic. Leave the mix to slake for 5-10 min and remix before use. Mix only sufficient quantity of adhesive for the immediate need. Proportion Approximately 1 bag of 20 to 50 Kg of VIRSUN SUN Block Adhesive with 12 to 15 liters of Water. Adjust the quantity of liquid to obtain proper consistency. Applications Thin bed mortar for laying blocks Before placing mortar, ensure the block work to be dry and surfaces cleaned properly. Place the mixed mortar on the block work In thin layers of 2 to 3 mm (or as required by engineers at the site) using ta rowel and place the next layer of blocks on the mortar. Keep Joints between the blocks as required by the site engineers and fill the Joints with the mixed mortar, using a trowel. Check the plumb of the wall while laying the blocks to keep the walls perfectly vertical to the plumb. Smoothing over the block work Before placing mixed mortar, apply a bonding layer of 1 to 2mm thick SUN Block Adhesive mortar using a trowel pressing down on the block work. Then apply SUN Block Adhesive at a thickness of 8 to 10mm and smoothen using a sponge or rubber / wooden float. When installing large blocks, spread higher thickness of SUN Block adhesive. Select proper type of notched trowel. As Adhesive to install tiles SUN Block Adhesive can be used as a thin-set adhesive to Install tiles on SUN Block/Fly ash brick walls. Use a suitable notch trowel to achieve the desired thickness of adhesive for installation of tiles on the wall. The most Important standard to keep in mind Is to ensure that the piece of block Is completely bedded In the mortar or adhesive with 100% coverage after Beat In. Installation Wet the surface and remove the excess water before applying the adhesive. Ensure the area Is shaded from sunlight. The adhesive shall be applied with the flat side of the trowel using a scraping motion to work the material into good contact with the surface to be covered. Additional mortar is then applied withthe notched edge of the trowel.

Send Inquiry
Request To Call Back
X


VIRSUN INDUSTRIES All Rights Reserved.(Terms of Use)
Developed and Managed by Infocom Network Private Limited.
Tradeindia
Back to top